Ultra Stick™ 40 ARFAssembly Manual
10 Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 7Installing the flap follows the same procedure as the aileron. Position the flap, check the gap
11Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 2Mark a center line on the joiner. It should slide into each wing panel up to the line. If not, li
12 Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 4Make sure the wing panels fit tightly together. Clean any epoxy using a paper towel and rubbing
13Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 2Position the wing bolt plate on the wing, aligning the holes with those in the wing. Trace the ou
14 Hangar 9 Ultra Stick 40 ARF Assembly ManualHorizontal Stabilizer InstallationRequired PartsFuselage Wing assemblyStabilizer1/4-20 x 11/2-inch nylo
15Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 5Use a felt-tipped pen to trace the outline of the fuselage on the stabilizer. Use a hobby knife a
16 Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 3Use 30-minute epoxy to glue the fin to the fuselage. Use a square to check the alignment of the
17Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 4Insert the tail gear wire into the rudder. It should fit as shown. Use 30-minute epoxy to glue on
18 Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 3Fit the rudder to the fin. Use a hobby knife and #11 blade to check the hinge gap and that the r
19Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 2Use a pin vise and 1/16-inch (1.5mm) drill bit to drill a hole in the center of each hinge slot i
2 Hangar 9 Ultra Stick 40 ARF Assembly ManualTable of ContentsContents of Kit and Parts Layout ...2Included Pa
20 Hangar 9 Ultra Stick 40 ARF Assembly ManualRadio InstallationRequired PartsFuselage assembly Servo with hardware (3)Control horn (2) Control horn
21Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 4Use a pin vise and 5/64-inch (2mm) drill bit to drill the holes for the screws. Use 2–3 drops of
22 Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 7With the rudder servo centered, attach the arm to the servo. With the rudder centered, use a fe
23Hangar 9 Ultra Stick 40 ARF Assembly ManualAileron Servo Installation (Aileron only) or Flap Servo Installation (Quad Flap Version)Required PartsW
24 Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 4Position the servo in the wing with the servo output shaft toward the aileron (or flap). Use a
25Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 8Use a pin vise and a 5/64-inch (2mm) drill bit to drill the two holes for the control horn screw
26 Hangar 9 Ultra Stick 40 ARF Assembly ManualAileron Servo Installation (Quad Flap Version)Required PartsWing assembly Control horn (2)Servo with ha
27Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 4Secure the servo in the wing using a #1 Phillips screwdriver and the hardware provided with the
28 Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 8With the control surface centered, use a felt-tipped pen to mark the pushrod where it crosses t
29Hangar 9 Ultra Stick 40 ARF Assembly ManualLanding Gear InstallationRequired PartsFuselage assemble Landing gearAxle with hardware (2)Main wheel, 2
3Hangar 9 Ultra Stick 40 ARF Assembly ManualPACKAGED IN BOXFuselage (1)Right wing with aileron (1)Left wing with aileron (1)Horizontal stabilizer w
30 Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 4Measure back 65/8-inches (168mm) (tail dragger) or 121/2-inches (317mm) (tricycle gear) and use
31Hangar 9 Ultra Stick 40 ARF Assembly ManualNote: Steps 2 through 4 are for the installation of the nose gear steering pushrod tube. If you are build
32 Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 5Attach the engine mount rails to the firewall using four 8-32 x 1-inch socket head screws and fo
33Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 9Use sandpaper to roughen the first 1-inch (25mm) of each end on the 133/4-inch (350mm) throttle p
34 Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 13Use a drill and 9/64-inch (3.5mm) drill bit to drill the four holes to mount the engine. It is
35Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 2Attach the nose wheel to the nose gear using two 4mm wheel collars and setscrews. Make sure to us
36 Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 6Use a felt-tipped pen to mark the nose gear wire against the inside edges of the engine mount ra
37Hangar 9 Ultra Stick 40 ARF Assembly ManualFuel Tank AssemblyRequired PartsFuel tank StopperAluminum tube (short) Aluminum tube (long)Metal disk (
38 Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 4Slide the fuel tube (red) on the short aluminum tube. The clunk will fit on the opposite end of
39Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 2Attach the pushrod connector to the hole in the servo arm as shown. Make sure to use threadlock o
4 Hangar 9 Ultra Stick 40 ARF Assembly ManualLarge Replacement Parts1. HAN173001 Fuselage2. HAN173002 Wing Set with Standard Ailerons3. HAN173003
40 Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 6Install the propeller and spinner following the instructions provided with the engine. Never use
41Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 3Mount the switch in the fuselage using the hardware included with the switch. The remote receiver
42 Hangar 9 Ultra Stick 40 ARF Assembly ManualAileron High RateUp 11/4-inch 32mm 32 degreesDown 11/4-inch 32mm 32 degreesAileron Low RateUp 7/8
43Hangar 9 Ultra Stick 40 ARF Assembly ManualELEVATOR-TO-FLAPSCouple elevator to flapsTight LoopsElevator upFlaps downWhat is elevator-to-flaps?An up-e
44 Hangar 9 Ultra Stick 40 ARF Assembly ManualFlight PreparationsFlight preparations must be checked each time you travel to the flying field. Because
45Hangar 9 Ultra Stick 40 ARF Assembly ManualSafety, Precautions and WarningsAs the user of this product, you are solely responsible for operating it
46 Hangar 9 Ultra Stick 40 ARF Assembly ManualWarranty ServicesQUESTIONS, ASSISTANCE, AND REPAIRSYourlocalhobbystoreand/orplaceofpurchasecanno
47Hangar 9 Ultra Stick 40 ARF Assembly ManualAcademy of Model Aeronautics National Model Aircraft Safety CodeEffective January 1, 2011A. GENERALA mode
16944.1 Revised 12/2010© 2010 Horizon Hobby, Inc.horizonhobby.com Hangar9.comThe Spektrum trademark is used with permission of Bachmann Industries, In
5Hangar 9 Ultra Stick 40 ARF Assembly ManualSafe Operating Recommendations• Inspectyourmodelbeforeeveryflighttomakecertainitis airworthy.•
6 Hangar 9 Ultra Stick 40 ARF Assembly ManualAileron Installation (Aileron Only)Required PartsWing panel (right and left)Aileron, full length (right a
7Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 4Use the hinges to place the aileron in position. Use a hobby knife to set the gap between the con
8 Hangar 9 Ultra Stick 40 ARF Assembly ManualAileron and Flap Installation (Quad Flap Only)Required PartsWing panel (right and left) Aileron (right a
9Hangar 9 Ultra Stick 40 ARF Assembly Manual Step 4Use the hinges to place the aileron in position. Use a hobby knife to set the gap between the con
Commentaires sur ces manuels